国产又粗又猛又爽又黄的黄牛视频-欧美日韩精品网址-国产成人麻豆h视频在线观看-蜜臀av区一二三爽免费播放-久久久伦理精品-99精品资源在线视频-伊人久久大香樵-久久人妻人人爽-性欧美少妇煌妇喷水,麻豆免费在线观看视频网站,天天射天天干天天要,91精品国自产拍老熟女露脸

麂皮絨羊羔絨搖粒絨面料復合機 貼合機詳細介紹

防水透氣膜膠點轉移復合機試機現場

如果還在擔心機器的質量？我們每年生產銷售幾百臺的機器設備、不到1％的維修率給您信心！

如果還在擔心機器的性能？我們?nèi)?**電子配件承諾、***的麂皮絨羊羔絨復合機防護技術給您保障！

如果還在擔心機器的售后服務？我們每款機器出廠前必須要經過您的試樣才能夠出廠 ！我們的售后承諾：一年保修，終身維護，定期提示保養

如果還在猶豫機器的價格？那么我希望您可以明白“一分錢一分貨”的真理。低端配置復合機不僅不***，而且在復合機方面也沒有保障！

復合機價格區間由經濟型到智能型5-40萬不等。總有一款適合您用的復合機械。全心全意為您量身訂制，打造出為您創造財富的不同檔次的機器。

麂皮絨羊羔絨復合機

特點：

1、整機在常規的膠點復合機的基礎上升級了自動糾偏、自動對中、自動開幅、自動吹廢料邊等功能。使復合的材料更具有涂膠均勻、復合平整、無拉伸變形、不起泡、不起皺、柔軟、透氣性佳、收卷整齊等優點。

2、復合材料品種多，尤其適用于面料與面料、面料與雙面或四面彈力型針織布、無紡布與皮革、海綿與絨布、海綿與皮革等材料的涂布復合；

3、收、放卷可根據不同的材料，來選擇適合的配置；

4、根據不同材料的特性，可增減部分裝置；

5、適用于水溶性和溶劑型膠涂布復合，實現一機多用的功能。

6、涂膠量與涂膠樣式可根據材料及實際需要調整。

7、滾筒加熱可采用電、蒸氣或?qū)嵊偷姆绞絹磉M行加熱。

8、機器輥面幅寬可根據實際材料的大幅寬來特定。

復合機操作調試技術中如何避免成品產生氣泡?鑫利龍***生產火焰復合機、油膠復合機、PUR熱熔膠復合機、水膠復合機等，下面跟著江蘇鑫利龍智能機械有限公司一起來了解一下吧!

　　提高膠黏劑的濃度或選用濕潤性好的膠黏劑太稀或濕潤性差的膠黏劑容易流淌，使基材上膠不均勻，從而易出現縱向或橫向流水紋。上膠量少的部分很可能出現氣泡�？梢酝ㄟ^提高膠黏劑的濃度或是選用濕潤性好的膠黏劑來減少氣泡的產生。基材電暈處理，有些塑料薄膜基材表面黏附膠黏劑的能力差，為了提高這類基材表面的黏附能力，保證涂布質量，要求基材的表面張力要達到42～56mN/cm左右�？梢栽谕坎记霸黾右惶纂姇炋幚砥鲗谋砻孢M行電暈處理，使表面起毛，以達到增強表面表面張力的作用，這樣就能提高基材表面的涂膠量以避免氣泡產生。

　　復合機操作人員要由經過嚴格培訓，傳動部分要設立保護裝置，機器一定要接地線，要具有良好的絕緣，并且在保護面板中操作。由于粘結是由膠分子和空氣中水分反應形成穩定粘結的固態結構，如果復合機機在空氣流動快速的環境下操作，膠就會容易快速冷卻凝結，從而影響膠流量噴頭組合，產生拉絲現象。因此，復合機機要在快速流通的環境下操作。

　　正確安裝與調節刮刀在涂布時，涂膠量的大小主要取決于網紋輥網穴的深淺，網穴越深涂膠量越多，水膠復合機網穴越淺涂膠量越少。正確調節刮刀可以保證上膠量更加均勻，從而減少或避免氣泡出現。涂布時，如果刮刀作用在網紋輥上的壓力過小，在有雜質混入時，就容易將刮刀頂起來形成縫隙，使涂布不均勻。由于網紋輥表面是不平滑的，如果刮刀安裝的角度過大，在它高速運轉時，彈性刮刀片容易發生震動或跳動，使膠液彈起來愛色麗，引起涂布量差異增大。一般刮刀與網紋輥接觸點的徑向夾角選擇在15～30°之間。

Characteristic:

1. The whole machine upgraded the functions of automatic deviation rectification, automatic alignment, automatic opening and automatic scrap blowing on the basis of conventional compound machine. The composite material has the advantages of uniform glue coating, smooth composite, no stretching deformation, no foaming, no wrinkle, soft, good air permeability, neat winding and so on.

2. There are many kinds of composite materials, especially suitable for coating and compounding of fabrics and fabrics, fabrics and double-sided or four-sided elastic knitted fabrics, non-woven fabrics and leather, sponge and flannel, sponge and leather, etc.

3. Receiving and unwinding can choose suitable configuration according to different materials.

4. According to the characteristics of different materials, some devices can be added or reduced.

5. It is suitable for water-soluble and solvent-based adhesive coating and compounding to realize multi-purpose function of one machine.

6. The amount and style of coating can be adjusted according to material and actual needs.

7. The drum can be heated by electricity, steam or heat conducting oil.

8. Machine roll width can be specified according to the actual material width.

How to avoid air bubbles in compound machine operation and debugging technology? Xin Lilong specializes in producing flame compound machine, oil glue compound machine, PUR hot melt glue compound machine, water glue compound machine and so on. Let&＃39;s follow Jiangsu Xin Lilong Intelligent Machinery Co., Ltd.

Increasing the concentration of adhesives or choosing adhesives with good wettability which are too thin or poor wettability are easy to flow, so that the adhesives on the base material are not uniform, so that the longitudinal or transverse flow lines are easy to appear. Bubbles are likely to appear in the part with less glue loading. Bubbles can be reduced by increasing the concentration of adhesives or by choosing adhesives with good wettability. In corona treatment of substrates, some plastic film substrates have poor adhesiveness to adhesives. In order to improve the adhesiveness of these substrates and ensure the quality of coating, the surface tension of substrates should reach about 42-56 mN/cm. Before coating, a set of corona processor can be added to corona treatment of the substrate surface to make the surface fuzz, so as to enhance the surface tension, so as to increase the amount of glue coating on the substrate surface to avoid bubbles.

The operator of the compound machine should be trained strictly, the transmission part should be equipped with protective device, the machine must be grounded wire, have good insulation, and operate in the protective panel. Because bonding is a solid structure formed by the reaction of glue molecule and water in air, if the compound machine operates in a fast air flow environment, the glue will be easily cooled and solidified quickly, which will affect the combination of glue flow nozzles and lead to wire drawing. Therefore, the compound machine should operate in a fast circulation environment.

When properly installing and adjusting the scraper in coating, the amount of glue coating mainly depends on the depth of the mesh hole of the mesh roller. The deeper the mesh hole, the more the glue coating amount, the less the glue coating amount of the shallow mesh hole of the hydro-glue compound machine. Correct adjustment of the scraper can ensure more uniform glue loading, thereby reducing or avoiding the appearance of bubbles. When coating, if the pressure of the scraper acting on the mesh roller is too small, when impurities are mixed in, it is easy to Jack the scraper up to form a gap, so that the coating is not uniform. Because the surface of mesh roller is not smooth, if the angle of scraper installation is too large, the elastic scraper blade is prone to vibrate or jump when it runs at high speed, which makes the glue springing up Aiseli and causes the difference of coating amount to increase. Generally, the radial angle between scraper and mesh roller contact point is between 15 and 30 degrees.